HOMEOWNERS: 750 sq. ft. minimum to receive a quote or sample.
CorruBracket 100T is the right way to attach almost anything to corrugated metal roof profiles common in North America, including solar panel mounting via rail or DirectAttached™ methods.
CorruBracket 100T is affixed to the crest of the corrugation, leaving the drainage plane free of holes to protect against leaks. For medium-duty applications, the bracket can be attached directly to the sheeting, accommodating ancillary attachment anywhere along the corrugation. For heavy-duty applications, the bracket can be fixed into the underlying substrate for additional support without crushing the corrugation. Having no messy sealants to apply, CorruBracket 100T comes with a factory-applied EPDM rubber gasket seal already on the base, and the reservoir conceals the EPDM from UV exposure, preventing UV degradation. CorruBracket 100T Mini is a bit shorter than its standard counterpart and has two pre-punched holes in its base rather than four. The Mini is the choice for attaching all kinds of rooftop accessories.
CorruBracket can be used to mount almost anything to corrugated metal roofing and is compatible with 7/8" and 3/4" corrugated roofing.
CorruBracket 100T is mounted directly into the crest of the corrugation, straddling the valley. No surface preparation is necessary; simply wipe away excess oil and debris, align and apply. Secure directly into the crest of the corrugation by driving the appropriate screws into the pre-punched holes, or pre-drilling the proper-sized hole through the pre-punched holes and riveting. The slotted top hole, which accommodates standard M8 nuts and bolts, simplifies alignment and maximizes flexibility in attaching ancillaries.
CorruBracket 100T Mini is a bit shorter than its standard counterpart and has two pre-punched holes in its base rather than four. The Mini is the choice for attaching all kinds of rooftop accessories: signs, walkways, satellite dishes, antennas, rooftop lighting, lightning protection systems, solar arrays, exhaust stack bracing, conduit, condensate lines, mechanical equipment—just about anything!*
*S-5!® Mini brackets are not compatible with, and should not be used with, S-5! SnoRail™/SnoFence™, ColorGard®, or X-Gard™ snow retention systems.
CorruBracket 100T is mounted directly into the crest of the corrugation, straddling the valley. No surface preparation is necessary; simply wipe away excess oil and debris, align and apply. Secure directly into the crest of the corrugation by driving the appropriate screws into the pre-punched holes, or pre-drilling the proper-sized hole through the pre-punched holes and riveting. The slotted top hole, which accommodates standard M8 nuts and bolts, simplifies alignment and maximizes flexibility in attaching ancillaries.
Please note: The above image illustrates the CorruBracket 100T. The steps remain the same for the CorruBracket 100T Mini; however, there will only be two fasteners used.
The S-5!® CorruBracket 100T is the right way to attach almost anything to corrugated roofing profiles common in North America, including PV via rail or DirectAttached™ methods.
All metal roofs need roofing underlayment. Synthetic underlayment provides an extra barrier of protection from water penetration and will protect your home from the elements. Learn about the differences between Sharkskin Comp, Ultra, and Ultra SA.
C purlins, Z purlins, and channel are available in a galvanized or primed red finish. Purlins and channel from 4” up to 12” deep. Immediately available in a 14 gauge metal thickness. Heavier and lighter gauges are available upon request.
Metal roofing fasteners, foam closures, fiberglass panels, trim and flashings, snow retention systems, galvanized square tube, rubber pipe boots, butyl sealant tape, ridge vent, solar solutions, more…..
It's a great resource for contractors, architects, and homeowners.
Easy to navigate learning center with videos and blogs that will answer your questions.
Are you planning to install your own metal roofing or metal siding? If so, you may want to read and watch these articles. We're sure you will find them useful and help you save time and money.
Looking for the differences between standing seam and exposed fastening systems for your metal roof? We compare both on cost, appearance, and...
Are you trying to determine which metal roofing styles are best? This video will discuss whether corrugated or standing seam is the best type of metal roof for your house. You will learn about the two types of residential metal roofing: exposed fastener or concealed fastener metal roofing panels.
We compare metal roof cost and performance for these two types of metal roof panels.
Are you evaluating metal roof options for your home and comparing r panel and standing seam? R-Panel is a lower-cost metal roofing and siding...
Choose Different Textures, Colors, Finishes, and Panel Types On Your Home Before You Decide.